Every homesteader should learn how to make a homemade stun gun and properly use it for self-defense. Good thing we have this easy and straightforward tutorial on how to make a homemade stun gun with materials that may already be in your hands!
Make An Easy DIY Stun Gun For Your Self-Defense
If you're not confident using a gun or your knife skills and prefer other weapons for self-defense, the stun gun just might be for you. I myself prefer this weapon in self-defense for personal reasons. A stun gun is an electrical weapon which is usually used to immobilize an attacker within arm's reach with a shock of electricity through a conductor. After it electrifies, this self-defense weapon renders a person incapable of doing anything due to pain and electrocuted sensory and motor nerves. But, why buy a stun gun when you can save by making one your own. Learn how to make your very own stun gun as you scroll down!
Let's Get Started!
What You Will Need:
- High-voltage inverter
- 20 cm PVC pipe
- Safety switch and a momentary switch (main button)
- 3 As battery and battery housing
- PVC coupling and soda bottle cap
- 2 small brass nails
- Black matte spray paint
- Cutter and pliers
- Glue gun
Step 1. Prepare Materials
As a homesteader who creates, builds, repurposes, and recycles, you may already have the materials to make a homemade stun gun at home or in your tool shed. For the inverter, a high voltage one, specifically one which can produce up to 400, 000 volts is recommended. Take out the outer layer of the inverter for the circuitry part to fit in. Using a cutter and pliers, carefully peel off the outer layer of the inverter. Once the outer layer is gone, the inverter will easily fit in the PVC pipe.
Step 2. Assemble The Circuitry
Prepare 3 triple A batteries and battery housing which will fit in the PVC pipe. The Taser should also have a safety switch with a push button that lights up when pressed so you can easily see if the Taser is on or off. You will also use a small momentary switch as the main button. Check out this basic circuit diagram or electronic schematic to assemble the basic circuitry.
Stun Gun Circuit Diagram
This elementary electronic schematic shows how you will assemble the circuits to make the Taser work. The battery is connected to the on and off safety switch which is the red LED button. It is then connected to the momentary switch that we press to make the Taser spark. This leads to the high voltage converter connected to the spark gap where the spark zaps through or between the two prongs which lead back to the battery.
Step 3. Prepare Stun Gun Housing
Now we go to our PVC pipe. Spray paint the pipe with a black matte spray paint and leave it to dry. Cut the pipe in two so you can have access to the batteries when replacing them after they've run out. Measure 13 cm from one end of the PVC pipe and cut from there so you have another 7 cm PVC pipe. Drill a hole for the main switch some 4 cm from the top of the longer PVC pipe where the momentary switch will be inserted. Use a PVC coupling to join the two separate PVC pipe pieces securely and for replacing the batteries.
Step 4. Assemble Stun Gun
Now to assemble the Taser stun gun, insert the safety switch with the red LED button to the shorter cut PVC pipe piece. Use glue to fasten the safety switch securely to the bottom of the shorter PVC pipe. Insert the rest of the circuitry including the momentary switch. You will need to seal the top of the stun gun and assemble the prongs. You can use a plastic soda cap but you will have to remove the extra plastic lining inside with a grinder so it fits the pipe perfectly. Puncture two holes on top of the plastic cap from which the two small brass nails will be inserted. Connect wirings to the brass nails which will serve as the prongs from which electricity can zap. Secure everything with hot glue and place the cap over the PVC pipe also securing it with glue.
Step 5. Finished Homemade Stun Gun
Finally, you can test your finished homemade stun gun! Make sure to take safety precautions and use this weapon for self-defense responsibly. Also, make sure to keep it out of reach of your youngsters.
Watch the full tutorial of making your DIY stun gun in this video:
There you have it, homesteaders! A simple and easy DIY stun gun tutorial. Don't you find this tutorial exciting and easy to follow too? Convenience aside, I'm pretty sure you'll find this DIY stun gun very useful one of these days. Heaven forbid, but better safe and prepared than sorry, right?
Are you going to give this homemade stun gun a try? Share your thoughts about it in the comments section below!
Up Next: How To Make A Knife In A Survival Situation Here.
Don't forget to follow us on Instagram, Twitter, Pinterest, and Facebook!
[email protected] says
STUPID, what the hell is High Voltage Inverter and where do you get one???
Theo Pieterse says
Excellent information.
I will fit mine into a pipe type walking stick because we continuously get robbed and never feel safe.
Thank you
Siacri says
It always frustrates me to read a tutorial that implies certain items can be found around the home then leaves out where the parts are located and in what product they can be recycled from.. This “inverter”..im confused.. what the hell is lying around that has a 400,000 inverter inside of it?
Farmer says
Most folks don’t know what a high voltage inverter is, much less have one laying around. With online prices of a few bucks, why bother?
Beebe Kent says
Easier yet, go down to your local farm store and purchase a livestock/cattle prod. Only difference is the intended target.
Nancy says
Excellent Idea. I’ve been touched with one of those and it isn’t fun. The prod is also long enough and heavy enough to swing like a club.
Michael Heath Sr. says
Your TUTORIAL video is nit working, why?
Margo says
I’m a 73-yr-old woman who thinks it may b easier 2 buy 1 since I don’t understand a lot of what u r talking about. I thot about I’d send it 2 sum1 who’d get it, but I think those folks r 2 busy. Good idea, tho. Thanks.
Leon Amer says
Problem with cattle prod idea – too big to fit in storage box between front car / truck seats so it is available to zap a wannabe carjacker as they reach into driver window. Also, even the DIY or purchased versions may be illegal in a state that treats the Constitution like toilet paper – NY, CA, etc., so if unsure of your local laws, consult an attorney or just pass this by completely.
online translate says
Remember, violence is never the answer, and it is always important to prioritize the safety and well-being of yourself and those around you.